Saving Energy Using Insulation & By Sealing Air Leaks

Saving Energy Using Insulation & By Sealing Air Leaks

Checking your home’s insulation is one of the fastest and most cost efficient ways to use a whole house approach to reduce energy waste and make the most of your energy dollars. A good insulating system includes acombination of products and construction techniques that protect a home from outside temperatures-hot and cold, protect it against air leaks, and control moisture. You can increase the comfort of your home while reducing your heating and cooling needs by up to

30% by investing just a few hundred dollars in proper insulation and sealing air leaks.

First, check the insulation in your attic, ceilings, exterior and basement walls, floors, and crawl spaces to see if it meets the levels recommended for your area. Insulation is measured in

R-values-the higher the R-value, the better your walls and roof will resist the transfer of heat. DOE recommends ranges of R-values based on local heating and cooling costs and climate conditions in different areas of the nation. State and local codes in some parts of the country may require lower R-values than the DOE recommendations.

Where to Insulate

 

Adding insulation in the areas shown below may be the best way to improve your home’s energy efficiency.

Crawl space Basement Attic

Walls

Floors

For customized insulation recommendations, visit energysavers.gov and check out the Zip Code Insulation Calculator, which lists the most economic insulation levels for your new or existing home based on your zip code and other basic information about your home.

Although insulation can be made from a variety of materials, it usually comes in four types; each type has different characteristics.

Rolls / Batts or blanketsare flexibleproducts made from mineral fibers, such as fiberglass and rockwool. They are available in widths suited to standard spacing of wall studs and attic or floor joists.

2×4 walls can hold R-13 or R-15 batts; 2×6 walls can have R-19 or R-21 products.

 

Loose-fill insulation is usually made of fiberglass, rock wool, or cellulose comes in shreds, granules,or nodules. These small particles should be blown into spaces using special pneumatic equipment. The blown-in material conforms readily to buildingcavities and attics. Therefore, loose-fill insulation is well suited for places where it is difficult to install other types of insulation.

 

Rigid foam insulation is typically more expensive than fiber insulation. But it’s very effective in buildings with space limitations and where higher R-values are needed. Foam insulation R-values range from R-4 to R-6.5 per inch of thickness (2.54 cm), which is up to 2 times greater than most other insulating materials of the same thickness.

 

Foam-in-place insulation-can be blown into walls and reduces air leakage.

 

Insulation Tips

 

* Consider factors such as your climate, building design, and budget when selecting insulation R-values for your home.

 

* Use higher density insulation, such as rigid foam boards, in cathedral ceilings and on exterior walls.

 

* Ventilation plays a large role in providing moisture control and reducing summer cooling bills. Attic vents can be installed along the entire ceiling cavity to help ensure proper airflow from the soffit to the attic to make a home more comfortable and energy efficient.

 

* Recessed light fixtures can be a major source of heat loss, but you need to be careful how close you place insulation next to a fixture unless it is marked IC-designed for direct insulation contact.

 

Should I Insulate My Home?

 

The answer is probably “yes”if you:

* Havean older home and haven’t added insulation. Only 20% of homes built before 1980 are well insulated.

 

* Are uncomfortably cold in the winter or hot in the summer – adding insulation creates amore uniform temperature and increases comfort.

 

* Build a new home, addition, or install new siding or roofing.

 

* Are paying high energy bills.

 

* Are bothered by noise from outside-insulation muffles sound.

 

Long-Term Savings Tip

 

One of the most cost-effective ways to make your home more comfortable year-round is to add insulation to your attic. Adding insulation to the attic is relatively easy and very cost effective.

 

To find out if you have enough attic insulation, measure the thickness of the insulation. If it is less than R-22 (7 inches of fiber glass or rock wool or 6 inches of cellulose), you could probably benefit by adding more. Most U.S. homes should have between R-22 and R-49 insulation in the attic.

 

If your attic has enough insulation and your home still feels drafty and cold in the winter or too warm in the summer, chances are you need to add insulation to the exterior walls as well. This is a more expensive measure that usually requires a contractor, but it may be worth the cost if you live in a very hot or cold climate.

 

You may also need to add insulation to your crawl space. Either the walls of the crawl space or the floor above the crawl space should be insulated.

 

How Much Insulation Does My Home Need?

 

For insulation recommendations tailored to your home, visit the DOE website at: http://www.energysavers.gov for the Zip Code Insulation Calculator

 

New Construction

 

For new construction or home additions, R-11 to R-28 insulation is recommended for exterior walls depending on location. To meet this recommendation, most homes and additions constructed with 2 in. x 4 in. walls require a combination of wall cavity insulation, such as batts and insulating sheathing or rigid foam boards. If you live in an area with an insulation recommendation that is greater than R-20, you may want to consider building with 2 in.x 6 in. framing instead of 2 in. x 4 in. framing to allow room for thicker wall cavity insulation-R-19 to R-21.

 

Today, new products are on the market that provide both insulation and structural support and shouldbe considered for new home construction or additions. Structural insulated panels, known as SIPS, and masonry products like insulating concreteforms are among these. Some homebuilders are even using an old technique borrowed from the pioneers, building walls using straw bales. Check online at www.energysavers.gov for more information on structural insulation. Radiant barriers (in hot climates), reflective insulation, and foundation insulation should all be considered for new home construction.

 

SealingAirLeaks

 

Warm air leaking into your home during the summer and out of your home during the winter can waste a lot of your energy dollars. One of the quickest dollar-saving tasks you can do is caulk, seal, and weather-strip all seams, cracks, and openings to the outside. You can save 10% or more on your energy bill by reducing the air leaks in your home.

 

Tips for Finding And Sealing Air Leaks

 

First, test your home for air tightness. On a windy day, hold a lit incense stick next to your windows,doors, electrical boxes, plumbing fixtures, electrical outlets, ceiling fixtures, attic hatches, and other locations where there is a possible air path to the outside. If the smoke stream travels horizontally, you have located an air leak that may need caulking, sealing, or weather-stripping.

 

Sources of AirLeaks in Your Home

 

Areas that leak air into and out of your home cost you lots of money:

 

Dropped ceiling

Water heater and furnace flues

Window frames Recessedlight All ducts

Electrical outlets and switches

Attic entrance

Doorframes

Plumbing and utility access

Sill plates

Chimney flashing

Insulation and Sealing Air Leaks

 

* Caulk and weather-strip doors and windows that leak air.

* Caulk and seal air leaks where plumbing, ducting, or electrical wiring penetrates through exterior walls,floors, ceilings, and soffits over cabinets.

* Install rubber gaskets behind outlet and switch plates on exterior walls.

* Look for dirty spots in your insulation, which often indicate holes where air leaks into and out of your house. You can seal the holes by stapling sheets of plastic over the holes and caulking the edges of the plastic.

* Install storm windows over single-pane windows or replace them with double pane windows.

* When the fireplace is not in use, keep the flue damper tightly closed. A chimney is designed specifically for smoke to escape, so until you close it, warm air escapes-24 hours a day!

* For new construction, reduce exterior wall leaks by either installing house wrap, taping the joints of exterior sheathing, or comprehensively caulking and sealing the exterior walls.

How and Where Does the Air Escape? 

 

*Plumbing penetrations 13%

*Windows 10%

*Floors, walls, and ceiling 31%

*Fireplace 14%

*Fans and vents 4%

*Doors 11%

*Ducts 15%

*Electric outlets 2%

Air infiltrates into and out of your home through every hole, nook, and cranny. About one-third of this air infiltrates through openings in your ceilings, walls, and floors.

A home inspection and thermal imaging inspection from Selman Home Inspection can help you identify areas of energy loss as well as moisture leaks and other areas of energy loss.

 

Refer Your Friends & Clients

We take pride in our work asHome Inspection Pros and strive to deliver the highest standards in quality, integrity, and value. We are dedicated to your real estate transaction and back every report with a more value and support than other Home Inspection Company. Here are a few of the benefits of referringSelman Home Inspections to your clients!

“Accurate Investment Protection You Can Trust”

FHA/HUD # F537
Septic #113423
Termite Tech # 660910
Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: